Fixed Competitive Price Deep Diamond Bit - Impregnated Core Bit – DeepFast
Fixed Competitive Price Deep Diamond Bit - Impregnated Core Bit – DeepFast Detail:
Design for higher ROP in drilling deeper and harder formations, PDC drill bit always drills from ground to bottom directly with less or even a single run, saving large amount of drill time and cost .
Differ from tricone bit, PDC drill bit runs with lower WOB but Higher RPM, so it usually works with downhole motor to pick up rotating speed.
The performance of PDC drill bit depends a lot on PDC cutters, we provide unique solution to specific requirement on varied formations.
Drilling in extremely hard formations It is suitable for coring in extremely hard abrasive formations, such as sandstone.
Features
◆Curved crown
The curved crown has a smooth core
◆Radiant waterway design
The bit has radiant waterway design which is suitable for high speed.
Technology
◆The self-sharpening impregnated insert
The self-sharpening impregnated insert keeps the cutting sharp during drilling.
◆The unique matrix formula
The unique matrix formula makes the matrix match the wear and formation,optimizes the cutting
Introduction:
It is suitable for coring in extremely hard abrasive formations, such as sandstone.
Features
1.Curved crown: The curved crown has a smooth core
2.The self-sharpening impregnated insert: The self-sharpening impregnated insert keeps the cutting sharp during drilling.
3.The unique matrix formula: The unique matrix formula makes the matrix match the wear and formation, optimizes the cutting edge and wear resistance of diamond which makes the bit obtain a better ROP.
4.Radiant waterway design: The bit has radiant waterway design which is suitable for high speed.
Product Specifications:
| IADC code | M842 |
| Number of blades | 15 |
| Total flow area | 1.0 in2 |
| Cutting structure | Pregnancy block |
| Standard gauge length | 1-1/2″（38.1 mm） |
| Upper buckle torque | 13.4~16.3KN•m |
| Core barrel size | 6-3/4″×4″(川7-4/5) |
Recommended Operating Parameters:
| Flow rate | 10~30 L/S |
| Rotating speed | 40~150RPM |
| Drilling pressure | 30~80 KN |
Impregnated Core Bit Complete Core Service
in Extremely Hard and Deep Formation
CHALLENGES
Extremely hard and abrasive formation
The depth is about 4,000 meters
Request for high recovery rate
SOLUTION
In order to solve these problems, DeepFast offers Impregnated Core Bit 8 1/2” x 4” DIC280 to achieve this goal in deep and hard formation.
RESULTS
With the core cut 1 15 meters in two runs. which is from 3805 to 3920 meters
The coring time is about 20 hours, and ROPIS 5.75 m/h
The recovery rate is more than 85%
Overview
In the Liaohe Oilfield in China, the operator Liaohe Oilfield Coring Technology Services planned to drilling in the deep well of 3805 meters. The formation is extremely hard and lithology is granite with the compress strength more than 24000PSL. Its objective was to core the 8 1/2” hole section of the well to recover the hard formation. The normal PDC core bit had only low recover rate and less core cut. Therefore Deepfast offers its new designed Impregnated Core Bit to achieve this goal in deep and hard formation.
Product detail pictures:
Related Product Guide:
With a positive and progressive attitude to customer's interest, our enterprise continually improves our products excellent to meet the wants of customers and further focuses on safety, reliability, environmental requirements, and innovation of Fixed Competitive Price Deep Diamond Bit - Impregnated Core Bit – DeepFast , The product will supply to all over the world, such as: Angola, New Orleans, Wellington, Many goods fully conform to the most rigorous of international guidelines and with our first-rate delivery service you will have them delivered at any time and in any place. And because Kayo deals in the entire spectrum of protective equipment, our customers don't have to waste time shopping around.
By Ivy from Islamabad - 2017.09.28 18:29
The manufacturer gave us a big discount under the premise of ensuring the quality of products, thank you very much, we will select this company again.
By Quintina from Eindhoven - 2018.10.31 10:02
